Testec SI Series TT-SI 9010 Oscilloscope Probe, Active, Differential Type, 70MHz, 1:100, 1:1000, 5kV Max
- RS Stock No.:
- 512-6078
- Mfr. Part No.:
- TT-SI 9010
- Brand:
- Testec
Image representative of range
View all Oscilloscope Probes
Available to back order for despatch 14/07/2023
Price Each
£747.41
(exc. VAT)
£896.89
(inc. VAT)
Units | Per unit |
1 + | £747.41 |
Alternative
This product is not currently available. Here is our alternative recommendation.

- RS Stock No.:
- 512-6078
- Mfr. Part No.:
- TT-SI 9010
- Brand:
- Testec
RoHS Status: Not Applicable
- COO (Country of Origin):
- TW
Technical Reference
Legislation and Compliance
RoHS Status: Not Applicable
- COO (Country of Origin):
- TW
Product Details
Testec 70MHz Active Differential Oscilloscope Probes
The Testec is an active differential oscilloscope probe that enables a conventional oscilloscope to display and measure in-circuit waveforms that are referenced to high common-mode voltages. It is capable of safely measuring differential voltages up to ±2500V AC and 7000V ac/dc. It supports bandwidths up to 70MHz.
This oscilloscope probe can measure signals below 700V by selecting the attenuation ration to 1:100.
This oscilloscope probe can measure signals below 700V by selecting the attenuation ration to 1:100.
Features and Benefits
Bandwidth is DC to 70MHz
Attenuation is 1:100/1:1000
Rise time is 5ns
Differential mode input voltage is 1:100 ±700V (DC+peak AC) or 700Vrms 1:1000 ±7000V (DC+peak AC) or 5000Vrms
Input impedance is 10Mohm ll10pF each side to ground
Common mode voltage range is 1:100 and 1:1000 ±7000V (DC+peak AC) or 2500Vrms
Non-destructive max. input voltage is 1:100 and 1:1000 ±7000V (DC+peak AC) or 2500Vrms
CMRR (typical) is -80dB at 50Hz and -60dB at 20kHz
Offset (typical) is <±5mV
Noise (typical) is 0.9mVRMS
Attenuation is 1:100/1:1000
Rise time is 5ns
Differential mode input voltage is 1:100 ±700V (DC+peak AC) or 700Vrms 1:1000 ±7000V (DC+peak AC) or 5000Vrms
Input impedance is 10Mohm ll10pF each side to ground
Common mode voltage range is 1:100 and 1:1000 ±7000V (DC+peak AC) or 2500Vrms
Non-destructive max. input voltage is 1:100 and 1:1000 ±7000V (DC+peak AC) or 2500Vrms
CMRR (typical) is -80dB at 50Hz and -60dB at 20kHz
Offset (typical) is <±5mV
Noise (typical) is 0.9mVRMS
Applications
Oscilloscope probes are used with oscilloscopes to enable the signals on the circuits being tested to be connected to the oscilloscope so that signals can be measured. These oscilloscope probes can be found in:
Performance conversion
Inverters
Motor speed indicators
Switch mode power supplies
Performance conversion
Inverters
Motor speed indicators
Switch mode power supplies
Certifications
CAT I 2500 VAC
CAT II 7000 VAC/DC
CAT II 7000 VAC/DC
Supplied with
Probe
4 x AA batteries
2 x Grabbers red & black
Instruction manual
Factory calibration certificate
4 x AA batteries
2 x Grabbers red & black
Instruction manual
Factory calibration certificate
Specifications
Attribute | Value |
Probe Type | Active, Differential |
Attenuation | 1:100, 1:1000 |
Bandwidth | 70MHz |
Maximum Common Mode Input Voltage | 5kV |
Connector Type | BNC |
Model Number p | TT-SI 9010 |
Number of Probes | 1 |
Series | SI |
Safety Category | CAT I 2500 V, CAT II 7000V |
Rise Time | 5ns |
Available to back order for despatch 14/07/2023
Price Each
£747.41
(exc. VAT)
£896.89
(inc. VAT)
Units | Per unit |
1 + | £747.41 |
Alternative
This product is not currently available. Here is our alternative recommendation.
