Bus Terminators

Bus terminators are electrical devices attached to the end points of a bus network to prevent the signals from reflecting off the end of the transmission line. They do this by supplying a load equal to the impedance of the cable.

How do bus terminators work?

Bus networks are connected in a chain formation by a single wire or series of wire segments. Once each component has detected a signal, the signal is absorbed by the bus terminator allowing other components to place their signals on the cable. Without the bus terminator, a signal placed on a wire by a component would bounce back and forth between the ends of the cable, preventing other cables from signaling.

What are bus terminators used for?

Bus terminators are used in ethernet networks, small computer system interfaces, dummy loads and control area networks. If you are looking for a device that can provide bidirectional input or output control and can be used in either digital or analogue devices consider a bus transceiver


...
Read more Read less

Filters

Viewing 1 - 6 of 6 products
Results per page
Description Price Termination Type Number of Bits Typical Resistance Maximum Supply Current Package Type Pin Count Dimensions Length Width Height Maximum Operating Supply Voltage Maximum Operating Temperature Minimum Operating Supply Voltage Minimum Operating Temperature
RS Stock No. 791-6296
Mfr. Part No.NUF2221W1T2G
£0.237
Each (On a Tape of 20)
Units
USB Line Termination 2bit 1.5 kΩ, 22 Ω 10 nA SC-88 6 2.2 x 1.35 x 1mm 2.2mm 1.35mm 1mm 5.25 V +125 °C - -55 °C
RS Stock No. 162-9614
Mfr. Part No.NUF2221W1T2G
£0.095
Each (On a Reel of 3000)
Units
USB Line Termination 2bit 1.5 kΩ, 22 Ω 10 nA SC-88 6 2.2 x 1.35 x 1mm 2.2mm 1.35mm 1mm 5.25 V +125 °C - -55 °C
RS Stock No. 761-9178
Mfr. Part No.LTC1694CS5#TRMPBF
£2.48
Each
Units
- - - 100 μA TSOT-23 5 2.9 x 1.75 x 0.9mm 2.9mm 1.75mm 0.9mm 6 V +70 °C 2.7 V 0 °C
RS Stock No. 919-9424
Mfr. Part No.LTC1694CS5#TRMPBF
£1.639
Each (On a Reel of 500)
Units
- - - 100 μA TSOT-23 5 2.9 x 1.75 x 0.9mm 2.9mm 1.75mm 0.9mm 6 V +70 °C 2.7 V 0 °C
RS Stock No. 186-9924
Mfr. Part No.STF202-22T1G
£0.33
Each (In a Pack of 25)
Units
USB Line Termination - 1.5 (Pull-Up) kΩ, 22 (Series) kΩ 5 μA TSOP 6 3.1 x 1.7 x 1mm 3.1mm 1.7mm 1mm 5.25 V +125 °C - -55 °C
RS Stock No. 186-9136
Mfr. Part No.STF202-22T1G
£0.136
Each (On a Reel of 3000)
Units
USB Line Termination - 1.5 (Pull-Up) kΩ, 22 (Series) kΩ 5 μA TSOP 6 3.1 x 1.7 x 1mm 3.1mm 1.7mm 1mm 5.25 V +125 °C - -55 °C
Related Products
Description:
The ROHM SOP-J8 1 channel 8 pin LIN transceiver has a data transfer speed of 20kbit/s. It is the best transceiver for the BUS system that needs LIN (Local Interconnect Network) master and slave protocol. This transceiver is available in low standby electricity consumption in sleep mode. The Local Interconnect ...
BD41000AFJ-C is a transceiver for the CXPI (Clock ...
Description:
BD41000AFJ-C is a transceiver for the CXPI (Clock Extension Peripheral Interface) communication. Switching between Master/Slave Mode can be done using external pin (MS pin). Low power consumption during standby (non-communication) using Power Saving function. Arbitration function stops the data output upon detection of BUS data collision. Also Fail-safe function stops ...
82C55A, CMOS Programmable Peripheral Interface82C59A, CMOS Priority Interrupt ...
Description:
82C55A, CMOS Programmable Peripheral Interface82C59A, CMOS Priority Interrupt Controller.
The SMSC FDC37C669 PC 95 Compatible Super I/O ...
Description:
The SMSC FDC37C669 PC 95 Compatible Super I/O Floppy Disk Controller: Infrared Support utilizes SMSC's proven Super Cell technology for increased product reliability and functionality. The FDC37C669 is optimized for motherboard applications. ISA Interface100 QFP Packaging5V Operating Voltage48 GPIO Pins1 Multi-Mode Parallel Port with EPP and ECP Support Game Port ...