Single Sided DIN 41612 Matrix Board FR2 with 1.02mm Holes 2.54 x 2.54mm Pitch, 220 x 100mm

Technical Reference
Legislation and Compliance
RoHS Certificate of Compliance
COO (Country of Origin): GB
Product Details

Economic Eurocard

The economical development board, designed for wire-to-wire connection of discreet components.
This board is very well suited to applications where there is a large number of common buses or signal lines.
Thanks to the APW cutter (stock number 543-535) used to cut tracks upon request, circuit production is very fast.

DIN Type Stripboards

Suitable for use with the KM6-II eurocard sub-rack systems

The double-sided microboards are designed for microprocessor applications where compatibility, flexibility, high density and screening are of prime importance. VCC rails and a VCC bus are provided but not connected, so that individual rails may be committed as required. 64//96-way DIN 41612 indirect edge connectors may be fitted at either end.
The 3U (100x160) and 6U (233.4x160) boards are available with plated through holes (pth) as an alternative to the standard types. These boards have the added advantage of linking the top with the bottom pads directly via the holes, thereby dispensing with the need to fit linking pins, etc. Also the integrity of the joint is improved as the solder forms round the component lead on both surfaces, in addition to flowing through the hole. This helps to produce a solid and reliable connection, which is very important in applications where a high degree of vibration may be encountered.
Eurocards are manufactured from either epoxy glass material (blue) to BS4584 Part 3 or 16, or SRBP (synthetic resin bonded paper) material to BS4584 Part 5. Card thickness is 1.6mm. Copper 305g/m2 (1oz/ft2). Holes 1.0mm (0.040in.) dia. are pre-drilled on a 2.54mm matrix and all cards can be used with indirect edge connectors to DIN41612 (see Connectors/Terminals) except SRBP stripboard.

Note

Single-sided microboards have the same wiring pattern as the double-sided types, but omit the ground plane and 0 Volt rails on the component side of the card.

Specifications
Attribute Value
Number of Sides 1
Hole Pitch 2.54 x 2.54mm
Dimensions 220 x 100mm
Length 220mm
Width 100mm
Base Material Synthetic Resin Bonded Paper
Hole Diameter 1.02mm
FR Material Grade FR2
Copper Thickness 35µm
Connection DIN 41612
14 In stock for FREE next working day delivery
Price Each
£ 12.48
(exc. VAT)
£ 14.98
(inc. VAT)
Units
Per unit
1 - 4
£12.48
5 - 9
£11.85
10 - 39
£11.23
40 +
£10.60
Related Products
Prototyping boards manufactured from epoxy glass material to ...
Description:
Prototyping boards manufactured from epoxy glass material to BS 4584 part 3 or 16. Card thickness is 1.6 mm. Copper is 305 g/m² (1 oz/ft²). Edge connector fingers are gold plated to a thickness of 1.5 microns. 1.0 mm (0.040 in.). Diameter holes are pre-drilled on a 2.54 mm (0.1 ...
Completely drilled boards, designed for the development of ...
Description:
Completely drilled boards, designed for the development of prototypes of analogue circuits.Thanks to the use of APW plugs, these cards are very versatile and allow discreet components to be connected wire-to-wire, or enable plugs and wrap pins to be fitted.
Matrix boards with 1mm holes on a 2.54mm ...
Description:
Matrix boards with 1mm holes on a 2.54mm pitch. The foil laminate allows wires to be placed in the same holes as the tails of the components, enabling very secure soldered connections to be made.A DIN 41612 connector with 96 / 96 contacts is fitted at each end.Supply rails are ...
SEG type is the optimum common earth type ...
Description:
SEG type is the optimum common earth type for high-frequency circuits2.54 mm pitch, board installation hole Ø 4 → 3.2.