440J Series Safety Enabling Switch, 3 Position, 2 NC, IP65

Technical Reference
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): US
Product Details

Enabling Switch, 440J Series

Hand-operated grip style enabling device. Underneath the rubber boot, called the trigger switch, the 440J enabling device has two three-position switches. The contacts are closed when the actuator is in the mid-position (partly depressed). The contacts are open when the actuator is in the rest (released) position and in the fully pressed position. When transitioning from fully pressed to released, the contacts remain open. The 440J meets the requirements of IEC 60947-5-8:2006, which was written to describe the performance and design requirements of three-position enabling devices. The model with the normally open contact is typically used as a jog or reset function. The safety system design must only allow the use of the jog or reset function when the trigger switch is in the mid-position.

2 N/C direct-opening action
Operating force; Position 2: 15 N approx., Position 3: 50 N max.
Direct opening force; 90 N
Maximum actuation frequency; 1200 operations per hour

Note

Base plate included. If operation of the switch contacts is all that is needed use the holding bracket 440J-A00N. Additional accessory brackets can be added to achieve various arrangements. The 440J-A01N right angle bracket accommodates the 440K-A11238 (standard actuator) which is used with the standard Trojan 6 or Trojan T15 and the 440G-A27011 (GD2 actuator) which is used with the GD2 interlocks. With two additional screws, the right angle bracket can be mounted to the 440J enabling switch for horizontal mounting. An actuator can also be mounted for vertical use without the 440J-A01N bracket. Mounting plate 440J-A02N has multiple pre-drilled and tapped holes to facilitate mounting of a single 440K-MT (MT-GD2) or 440K-T (Trojan) interlock. Four additional through-holes at the corners allow mounting of the plate to a flat surface. The 440J-A03N accessory mounts to the enabling switch base plate and has two sets of holes to accommodate either two standard or two GD2 actuators. This arrangement is used in conjunction with the 440K-A04N accessory. The U-shaped 440J-A04N can accommodate two interlocks: either 440K-MT or 440K-T. Using the 440J-A03N plate with dual actuators, a total of eight contacts, four in each switch, can be made available for the safety and control system.

Enabling Switch

Specifications
Attribute Value
Series 440J
Contact Configuration 2 NC
Number of Positions 3
IP Rating IP65
Housing Material Polyamide
Dimensions 260 x 46 x 58 mm
Depth 58mm
Length 260mm
Width 46mm
14 In stock for FREE next working day delivery
Price Each
£ 136.00
(exc. VAT)
£ 163.20
(inc. VAT)
Units
Per unit
1 +
£136.00
Related Products
Different types of coded magnetic switchesManipulation safety by ...
Description:
Different types of coded magnetic switchesManipulation safety by multi-codingRedundance by NO and NC contactsCannot be operated with conventional magnets3, 6 and 9 m cable or connector versionsSturdy plastic enclosuresSwitching distances 3 or 4 mm, depending on typeNO contact and NC contact combined for connection to magnetic controller Temperature range -5°C ...
Magnet switches designed for mounting on movable protective ...
Description:
Magnet switches designed for mounting on movable protective guards such as covers, flaps and doors.Suitable for areas where cleaning, disinfecting or contamination is involvedIP67 ratedFor a suitable safety relay, use 528-0908Effective operating distance 4-14mmFor a suitable coded magnet, use stock no 528-0857Cable length of 3m.
Non-contact actuationMagnetic coded sensingHigh tolerance to misalignment2 N/C ...
Description:
Non-contact actuationMagnetic coded sensingHigh tolerance to misalignment2 N/C reed safety outputsSwitching current: 200 mA @ 24VdcIP67 protection ratingCategory 1 device per EN 954-1, dual channel contacts suitable for Cat 3 or 4 systems.
The Schneider XCS-DMR coded magnetic safety switches are ...
Description:
The Schneider XCS-DMR coded magnetic safety switches are designed for monitoring the doors, covers and guards of industrial machines with imprecise guiding and low inertia. These safety switches are ideally suited for machines subjected to frequent washing or liquid spray. They protect the operator by immediately stopping any dangerous movement ...