Pico Technology TA Series TA044 Oscilloscope Probe, Active, Differential Type, 70MHz, 1:100, 1:1000, BNC Connector
- RS Stock No.:
- 898-6750
- Mfr. Part No.:
- TA044
- Brand:
- Pico Technology
Sorry, we couldn't check our stock levels right now. Please try refreshing the page.
Not available for guaranteed pre 9am/10am delivery
Added
Price Each
£749.00
(exc. VAT)
£898.80
(inc. VAT)
Units | Per unit |
1 + | £749.00 |
- RS Stock No.:
- 898-6750
- Mfr. Part No.:
- TA044
- Brand:
- Pico Technology
Technical Reference
Legislation and Compliance
- COO (Country of Origin):
- TW
Product Details
Pico Technology Oscilloscope Probe
The Pico Technology TA044 oscilloscope probe is an active differential probe, suitable for high common-mode voltage measurement applications up to ±7000V. It can be used with a signal speed of up to 70Hz. This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high voltage differential measurements.
By selecting attenuation ratio 1:100, this oscilloscope probe can measure signals below 70V to get higher resolution and less noise. Otherwise, set the attenuation to 1:1000.
By selecting attenuation ratio 1:100, this oscilloscope probe can measure signals below 70V to get higher resolution and less noise. Otherwise, set the attenuation to 1:1000.
Features and Benefits
Bandwidth is DC to 70MHz (–3dB)
Attenuation ratio is 100:1/1000:1
Accuracy is ±2%
Input impedance is 10Mohm ll10pF each side to ground
Differential range is (100:1) ±700V (DC + peak AC) or 700VRMS
Maximum differential is (1000:1) ±7000V (DC + peak AC) or 5000VRMS
Common mode range is ±7000V (DC + peak AC) or 2500VRMS (100:1 & 1000:1)
Absolute maximum voltage is ±7000V (DC + peak AC) or 2500VRMS (100:1 & 1000:1)
Absolute maximum voltage is (differential mode) ±7000V (DC + peak AC) or
5000VRMS (100:1 & 1000:1)
Swing is ±7V into 50kohm load
Offset (typical) is <±5mV
Noise (typical) is 0.9mVRMS
Source impedance is (typical) 50ohm
CMRR (typical) is 80dB at 6Hz and 50dB at 1MHz
Ambient operating temperature ranges between -10°C and 40°C
Power requirement 4xAA cells or 6VDC/200mA mains adaptor or regulated 9VDC/120mA mains adaptor
Input lead length 600 mm
BNC lead length 900 mm
Dimensions (LxWxH): 202 x 83 x 38 mm
Attenuation ratio is 100:1/1000:1
Accuracy is ±2%
Input impedance is 10Mohm ll10pF each side to ground
Differential range is (100:1) ±700V (DC + peak AC) or 700VRMS
Maximum differential is (1000:1) ±7000V (DC + peak AC) or 5000VRMS
Common mode range is ±7000V (DC + peak AC) or 2500VRMS (100:1 & 1000:1)
Absolute maximum voltage is ±7000V (DC + peak AC) or 2500VRMS (100:1 & 1000:1)
Absolute maximum voltage is (differential mode) ±7000V (DC + peak AC) or
5000VRMS (100:1 & 1000:1)
Swing is ±7V into 50kohm load
Offset (typical) is <±5mV
Noise (typical) is 0.9mVRMS
Source impedance is (typical) 50ohm
CMRR (typical) is 80dB at 6Hz and 50dB at 1MHz
Ambient operating temperature ranges between -10°C and 40°C
Power requirement 4xAA cells or 6VDC/200mA mains adaptor or regulated 9VDC/120mA mains adaptor
Input lead length 600 mm
BNC lead length 900 mm
Dimensions (LxWxH): 202 x 83 x 38 mm
Applications
Safe measurement in power circuit
Acquisition of low speed balanced differential signals found in serial communications buses
Transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays
Signals in the milliV range from sensors and other instrumentation
Acquisition of low speed balanced differential signals found in serial communications buses
Transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays
Signals in the milliV range from sensors and other instrumentation
Certifications
IEC-1010.2-031 CAT I certified
Pollution Degree 2 certified
Pollution Degree 2 certified
Note
The spring hooks supplied with this probe are rated at 1000 V.
Specifications
Attribute | Value |
---|---|
Probe Type | Active, Differential |
Attenuation | 1:100, 1:1000 |
Bandwidth | 70MHz |
Maximum Common Mode Input Voltage | 5kV |
Connector Type | BNC |
Model Number p | TA044 |
Number of Probes | 2 |
Safety Category Level | CAT I |
Series | TA |
Safety Category | 2500 V, CAT I 7000V |
Rise Time | 5ns |
- RS Stock No.:
- 898-6750
- Mfr. Part No.:
- TA044
- Brand:
- Pico Technology
Related links
- Testec 8000 Series TT-SI 8010A Oscilloscope Probe Differential...
- Pico Technology TA Series TA041 Oscilloscope Probe Differential...
- Testec 8000 Series TT-SI 8110 Oscilloscope Probe Differential Type...
- Pico Technology TA Series TA043 Oscilloscope Probe Differential...
- Testec 8000 Series TT-SI 8050 Oscilloscope Probe Differential Type...
- Testec 8000 Series TT-SI 8051 Oscilloscope Probe Differential Type...
- Testec 8000 Series TT-SI 8071 Oscilloscope Probe Differential Type...
- Testec TT-SX 9000 Series TT-SX 9002 Oscilloscope Probe...