Tektronix P5200A Oscilloscope Probe, Probe Type: Differential, High Voltage 50MHz 1kV 1:50, 1:500
- RS Stock No. 734-5029
- Mfr. Part No. P5200A
- Brand Tektronix
Tektronix High Voltage Differential Probes TMDP, THDP and P52xxA Series
Tektronix high voltage probing solutions offer safety and accuracy in applications which include: floating measurements; switching power supply design; motor drive design; electronic ballast design; CRT display design; power converter design and service; power device evaluation.
Overrange indicator
Safety certified
Switchable attenuation
Switchable bandwidth limit
Cable length 1.5m (THDP & TMDP), 1.8m (P52xxA)
Note
TMDP and THDP Series probes have the TekVPI® interface which enables smart communication between oscilloscope and probe - each TekVPI probe features controls and indicators located on the probe compensation box, designed to provide quick and easy access to the probe's most commonly required setup controls and operating status. P52xxA Series probes have the Tektronix TekProbe® interface which communicates scale information to the oscilloscope. Tektronix high voltage differential probes include: TMDPO200 ( 752-7366 ); THDPO200 ( 752-7357 ); THDP0100 ( 752-7353 ); P5200A ( 734-5029 ); P5202A ( 734-5022 ); P5205A ( 734-5026 ); P5210A ( 734-5035 ).
Tektronix Oscilloscope Probes
The Tektronix is active deferential voltage oscilloscope probe has a bandwidth of 50MHz and permits selection of 50x or 500x attenuation. It converts floating signals to low voltage ground-referenced signals that can be displayed safely and easily on any ground-referenced oscilloscope.
Note:
TMDP and THDP Series probes have the TekVPI® interface which enables smart communication between oscilloscope and probe - each TekVPI probe features controls and indicators located on the probe compensation box, designed to provide quick and easy access to the probe's most commonly required set-up controls and operating status. P52xxA Series probes have the Tektronix TekProbe® interface which communicates scale information to the oscilloscope.
The P5200A can be used with any oscilloscope and enables users to safely make measurements of floating circuits with their oscilloscope grounded.
Supplied with
• 2 hook clips
• 2 pincer clips
• 2 alligator clips
• 2 extension cables
Warning
Do not use the P5200A with scopes that have floating inputs (isolated inputs), such as the Tektronix TPS2000 Series. The P5200A requires an oscilloscope or other measurement instruments with grounded inputs.
Features and Benefits
• Bandwidth is DC to 50MHz
• Attenuation ratio is 1:50 and 1:500
• Input impedance is 5Mohmll4pF
• Maximum common mode voltage is ±1.3KV
• Maximum Input voltage is 1000V CAT II
• Wide compensation range (7pF to 30pF)
• CMRR (typical) is 100kHz: > -60dB 3.2MHz: > -30dB 100MHz: > -26dB
• Overrange indicator
• Safety certified
• Switchable attenuation
• Switchable bandwidth limit
• Cable length 1.5m (THDP & TMDP), 1.8m (P52xxA)
Applications
• Floating measurements
• Switching power supply design
• Motor drive design
• Electronic ballast design
• CRT display design
• Power converter design and service
• Power device evaluation
• BNC interface (P5200A probes)
• TekVPI interface (TMDP and THDP Series probes)
• TekProbe interface
Certifications
• EN 61010-031
• UL 61010-031 listed
• CAN/CSA-C22.2
• IEC 61010-031
• IP20 Rating
• CAT II
Supplied with
2 hook clips, 2 pincer clips, 2 alligator clips, 2 extension cables
Warning
- Do not use the P5200A with scopes that have floating inputs (isolated inputs), such as the Tektronix TPS2000 Series. The P5200A requires an oscilloscope or other measurement instrument with grounded inputs.
| Attribute | Value |
|---|---|
| Probe Type | Differential, High Voltage |
| Attenuation | 1:50, 1:500 |
| Bandwidth | 50MHz |
| Maximum Common Mode Input Voltage | 1kV |
| Model Number p | P5200A |
| Safety Category Level | CAT II |
| Safety Category Voltage | 1000V |
| Series | P52XXA |
| Safety Category | CAT II 1000 V |
