Magnatec L298N, Brushed Motor Driver IC, 46 V 4A 15-Pin, MULTIWATT V

  • RS Stock No. 636-384
  • Mfr. Part No. L298N
  • Brand Magnatec
Technical Reference
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

L298 Dual Full Bridge Motor Driver

ST Microelectronics presents its L298 dual full bridge driver series. The L298 series from ST is an integrated high voltage, high current dual full bridge driver. These devices are specially designed to accept standard TTL logic and drive inductive loads in Relays, Solenoids, DC and Stepper Motors. Featured are two enable inputs that allow the L298 to be enabled or disabled independently of the input signals. The emitters of the lower transistors of each bridge are connected together, the corresponding external terminal can be used to connect an external sensing resistor. In addition, a supply input is provided so that the logic works at a lower voltage.

Features

  • Operating supply voltage up to 46 V

  • Total DC current of up to 4 A

  • Low saturation voltage

  • Over-temperature protection

  • Logical "0" input voltage up to 1.5 V (high noise immunity)

What are Motor Driver IC's?

Motor Driver ICs are current amplifiers and are an essential component of motor interfacing. The motor driver integrated circuit chip acts as the interface between a microprocessor or microcontroller, and a motor. As microprocessors tend to operate at lower currents, and motors at higher, motor driver ICs are needed to supply current to the motor as needed. The RS Components range of Motor Driver ICs includes models from leading brands, in various types and configurations to support your design needs.

Motor Controllers & Drivers, STMicroelectronics

Specifications
Attribute Value
Motor Type Brushed DC
Output Configuration Dual Full Bridge
Maximum IGBT Collector Current 4A
Maximum Collector Emitter Voltage 46 V
Mounting Type Through Hole
Package Type MULTIWATT V
Pin Count 15
Maximum Operating Supply Voltage 46 V
Minimum Operating Supply Voltage 4.8 V
Width 5mm
Minimum Operating Temperature -25 °C
Height 10.7mm
Dimensions 19.6 x 5 x 10.7mm
Maximum Operating Temperature +130 °C
Length 19.6mm
393 In stock for FREE next working day delivery
Price Each
£ 4.02
(exc. VAT)
£ 4.82
(inc. VAT)
Units
Per unit
1 - 9
£4.02
10 +
£3.33
Packaging Options:
Related Products
From Microchip the MTD6508 device is a 3-phase ...
Description:
From Microchip the MTD6508 device is a 3-phase full-wave sensorless driver for brushless DC (BLDC) motors that features a 180° sinusoidal drive, high torque output and silent drive. The MTD6508 is designed to cover a wide range of motor characteristics with the minimum of external components. Speed control can be ...
Allegro ICs for half- and full-bridge drives (brush ...
Description:
Allegro ICs for half- and full-bridge drives (brush motor, dc motor driver, dc brushed motor, brush dc motor)Brush DC motors are the most widely used drivers due to their low cost and simple drive control options. Typical brush DC motors consist of a rotating electromagnet surrounded by a permanent magnet. ...
The A5995 is designed to operate at voltages ...
Description:
The A5995 is designed to operate at voltages up to 40 V while driving two DC motors at currents up to 3.2 A. The A5995 includes a fixed off-time pulse-width modulation (PWM) regulator for current control. The DC motors are controlled using standard PHASE and ENABLE signals. Fast or slow ...
The range of power drivers by STMicroelectronics are ...
Description:
The range of power drivers by STMicroelectronics are designed to drive a motor or a complex load through the logic commands at its input. They can be used with microcontrollers, DSPs or FPGAs in a motor or motion control system. The power drivers come in Dual Full Bridge, Full Bridge ...