Ring Seal TSN513C, 60mm ID

  • RS Stock No. 506-680
  • Mfr. Part No. TSN513C
  • Brand SKF
Technical Reference
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): SE
Product Details

Felt Ring Seals Type C

Felt ring seals are simple but efficient seals for use with grease lubrication. They can be operated at peripheral speeds of up to 4 m/s (800 ft/min). The seals can be used at higher speeds, but a small gap forms between the felt and the shaft. As a result the seals become non-rubbing gap-type seals.
For pillow block housings with bearings on adapter sleeves and shafts not exceeding a surface roughness of Ra 3.2 μm, the felt ring seals are split. Oil-impregnated felt is inserted into Light Alloy half-rings and the seals inserted into the grooves of the housing. The rubber O-section cords should be put into the grooves first as they prevent the seals from turning.
SNL pillow block housings for bearings mounted on the cylindrical seatings of stepped shafts, sizes 205 to 218 inclusive, can also be supplied with felt seals. In this case, the seals consist of loose felt strips that can be inserted into the sealing grooves. Before mounting the FS felt strips, soak for a few minutes in hot oil. The permissible angular misalignment for felt seals is approximately 0.5°. The seal counterface on the shaft should be ground and the surface roughness should not exceed Ra 3.2 μm (125 RMS). The axial movement on the shaft relative to the housing is not limited when felt seals are used. The ready-to-mount felt ring seals (in Light Alloy half-rings) are always supplied in packs of two. The felt ring seals are identified by the designation prefix TSN followed by the size identification and the suffix C, for example, TSN 511 C.

Plummer Blocks, Bearing Lubrication and Accessories

Specifications
Attribute Value
Inside Diameter 60mm
Material Felt
Centre Height 95mm
Mount Hole Size 20 mm
Length 315mm
Depth 120mm
Overall Height 175mm
Mount Hole Centre-to-Centre 260mm
For Use With Type C for Plummer Block Housed Units
2 in stock for FREE next working day delivery
7 available from Europe for delivery within 1 working day(s).
Price Each
£ 10.82
(exc. VAT)
£ 12.98
(inc. VAT)
Units
Per unit
1 - 4
£10.82
5 - 9
£10.38
10 - 24
£10.17
25 +
£9.96
Related Products
Double-lip L seals are made of thermoplastic elastomer ...
Description:
Double-lip L seals are made of thermoplastic elastomer (TPE) and can be used for peripheral speeds of up to 13 m/s (2600 ft/min). In all other aspects, they are the same as the G seal. However they are only available for metric shafts in housing sizes 507-522, as of March ...
The main benefit of split plummer block housings ...
Description:
The main benefit of split plummer block housings is their easy installation; pre-assembled shafts can be mounted in them. SNL Plummer blocks are primarily intended for self-aligning ball bearings, spherical roller bearings and CARB bearings. Stiff Design - Insensitive to uncontrolled tightening of the attachment bolts and low operating temperatures ...
The bearing seating in the housing is sufficiently ...
Description:
The bearing seating in the housing is sufficiently wide to enable the bearing to be displaced axially Bearings which are to locate a shaft axially in both directions (locating bearings) must always be fixed axially in position in the housing bore by locating rings at both sides The locating rings ...
Cast iron self lubricated pillow block bearings from ...
Description:
Cast iron self lubricated pillow block bearings from NSK. These pillow block bearings are easy to fit and long lasting. Designed to accommodate an initial housing misalignment of up to 0.030 radians. Made from cast iron to BS1452Spherical bearing insert accommodates initial misalignment Nitrile/fabric seals Supplied with full fitting instructionsC3 ...