Copper Pipe Fittings

Why use copper pipe fittings?

Copper is used as it can tolerate very high temperatures and as such, is used widely for central heating applications

Different types of Fittings

Adapters
Adapters are used to extend runs, or to simply change the connection type at the end of a pipe

Bushings
Bushings are used to join pipes of different sizes, usually by reducing a larger fitting down to a smaller pipe.

Couplings
A coupling is used to extend the run of a pipe, or change pipe sizes

Elbows
If you need to change the direction of flow, elbows are likely your best bet. Produced primarily in 90 and 45 degree angles (unique sizes like 22.5 and 60 are also available), elbows can be threaded or sweated, and are one of the most crucial fittings used in plumbing

Tees
When more than one branch is required of a water supply, tees are the way to go. Essentially a long coupling with an outlet on the side, these fittings feature their outlets at 90° from the inlet, and are sized according to their "run" (the horizontal, or straight-through dimension of the fitting), and the side outlet (the "top" of the fitting, 90 degrees off the run). When the run of a tee is smaller than the side outlet, it's often referred to as a "bull head" fitting.

Caps and Plugs
A cap, as its name suggests, is a cap that goes over the end of a pipe, creating a dead end. Plugs also stop up a pipe or tube system, but are plugged, like a stopper, into the end of the pipe.

Cross type Fitting
Cross type fittings contains 4 opening in 4 directions. These are connected when there are 4 pipes are meeting at a point.

...
Read more Read less

Filters

Viewing 1 - 9 of 9 products
Results per page
Description Price Fitting Direction Fitting Type Push Fit Pipe Size Threaded Connection Gender Thread Size Thread Standard
RS Stock No. 712-6786
Mfr. Part No.75531
£24.38
1 Pack of 10
Pack(s)
90° Elbow 15mm - - - -
RS Stock No. 712-6799
Mfr. Part No.75556
£3.355
Each (In a Pack of 2)
Units
- Equal Tee 15mm - - - -
RS Stock No. 712-6780
Mfr. Part No.75501
£1.968
Each (In a Pack of 5)
Units
Straight Coupler 15mm - - - -
RS Stock No. 712-6792
Mfr. Part No.75532
£3.52
Each (In a Pack of 2)
Units
90° Elbow 22mm - - - -
RS Stock No. 712-6831
Mfr. Part No.75591
£2.39
Each (In a Pack of 2)
Units
- End Stop 15mm - - - -
RS Stock No. 712-6837
Mfr. Part No.75510
£2.70
Each (In a Pack of 2)
Units
Straight Coupler 15mm 1/2 in G Female Female 1/2in G
RS Stock No. 712-6796
Mfr. Part No.75502
£2.935
Each (In a Pack of 2)
Units
Straight Coupler 22mm - - - -
RS Stock No. 712-6812
Mfr. Part No.75537
£2.62
Each (In a Pack of 2)
Units
90° Street Elbow 15mm - - - -
RS Stock No. 712-6856
Mfr. Part No.75592
£3.00
Each (In a Pack of 2)
Units
- End Stop 22mm - - - -
Related Products
The Pegler Yorkshire 28mm 90° copper S12 elbow ...
Description:
The Pegler Yorkshire 28mm 90° copper S12 elbow is used with hard and half-hard copper tubes. It has a press-fit connection type. • Ambient temperature ranges between 15°C and 95°C• Clean, rapid and heat-free jointing. No complicated clamping techniques, long preparation procedures or waiting for adhesive to dry • Electrical ...
The Pegler Yorkshire 22mm copper S1 straight coupling ...
Description:
The Pegler Yorkshire 22mm copper S1 straight coupling is used with hard and half-hard copper tubes. This product is suitable for joining copper. It has a press-fit connection type. • Ambient temperature ranges between 15°C and 95°C• Clean, rapid and heat-free jointing. No complicated clamping techniques, long preparation procedures or ...
CEJN's non drip couplings are designed for low-pressure ...
Description:
CEJN's non drip couplings are designed for low-pressure fluid and vacuum applications, and their performance and safety requirements. The product range is ideal for connecting all types of fluid lines. All have a single disconnect stage. Nickel-plated brass body, NBR (Nitrile rubber) seal, stainless steel spring. Non-drip, no air inlet ...
This Georg Fischer reducer is ideally used for ...
Description:
This Georg Fischer reducer is ideally used for industrial pressure applications such as water and gas. The reducer provides an extensive combination of possibilities and with an ease of assembly. 4 mm pin connectors ensure a secure fit between all ends of the pipe. Integral pipe fixation Max pressure – ...